Does anybody have the flash file 4M0 907 217 "D" for the Audi Q7 4M camera.
Hello I have a DD15 ECM with the label A 000 446 76 35 /002, however, I cannot find any protocol that come close to this info, the closes one I found in KTAG is the plugin 542: A 001 446 40 35 /001.
is this two ECM's compatibles in protocols?
Both of them are HDEP, just one is US AC and the other EU CA.
Any clue guys?
Possible protocol: https://www.dropbox.com/s/w1q3ppt243wuqd...3.pdf?dl=0
ECM: A 000 446 76 35 /002
Could someone help me. I keep getting error on fresh install of SA 4.2
"the incremental Update profile is not complete. Please choose an occurance setting and at least one model"
What is the point of downloading ETK? Everything seems to be the exact as same as realoem.com
Is it so that you can have the catalog if you don't have internet access or what? Just trying to figure what if it's a waste of space or not.
Xtuner E3 is the update version of Vpecker easydiag scanner that supports 70 US domestic, European, Asian, Australian and Chinese vehicles makes
Multi-language: Italian,English,, Japanese, German, Russian, French, Spanish, Portuguese, Polish,Turkish, Dutch, Hungarian, Korean, Czech, Arabic, Indonesian, Persian, Thai, Vietnamese, Finnish, Swedish, Romanian, Bosnian
XTUNER E3 Diagnostic System Coverage
ME-Motor electronics, CDI-Common Rail Diesel Injection, ETC-Electronic transmission control, ESM-Electronic selector module, SBC - Sensotronic Brake Control, ESP-Electronic stability program, BAS-Brake assist, Suspension, TPC-Tire pressure monitor, Airbag, CGW-Central gateway, EIS-Electronic ignition switch, OCP-Overhead control panel, UCP-Upper control panel, XALWA-Xenon headlamp, HRA-Headlamp range control, ATA-Anti-theft alarm system, IC-Instrument cluster, ASSYST-Active Service System, SCM-Steering column module, EPS-Electrical power steering, PTS - Parktronic system, EPB-Electric parking brake, COMAND/AUDIO, CD/DVD, TV tuner, CTEL-Cellular telephone, DCM-Door control module, ESA driver-Electric seat adjustment driver, ESA passenger-Electric seat adjustment passenger, AAC-Air conditioning, WSS-Weight sensor system, SVMCM-Special vehicle multifunction control module, etc.
XTUNER E3 WiFi Scanner Function Coverage
Quick Test, Read ECU Info., Read DTCs, Erase DTCs, Clear learning value, Data Stream, Actuations, Read freeze frame data, Read/Write VIN, Basic Reset, Control unit adaptations, Throttle adaptations, Air bleeding, Level calibration, Theft alarm Reset, Key programming, Oil change, Idle speed learning, Idle speed Adjustment, Ignition timing adjustment, Camshaft timing control learning, Maintenance functions, ECU Initial startup, ECU initialization, etc
Test scanner on Win7/Win10 tablet:
video demo will be added soon...
I need your help I have a Cadillac cts 05,
After replacing the pcm, it was reprogrammed and also 10 minutes relearn
The car start, but after one minute theft is on, I turn off the car and then I turn the car on again, and the same
What is wrong?
codes with scan tool b1000
Thanks in advance
hi, I need some help, I have a withe cnh dpa5 , coming from dealership, but I do not get any communication to EST 8.4. when I connect to tractor I get all the light flahing once then only power stay red. laptop will beep when connect USB or disconnect ... when look under parameter of USB device it say setup not complete , no driver, tried to scan for driver online but after 10 minutes haven't found anything..any help would be appreciate..
i have a customer asking for a EGR DPF DEF delete on a 2012 mitsubishi fuso
if any on can help me with this pm me the price
I have replaced my old ECM in my Jeep G Ch 2000 by an old one. It runs but stalls after 1-2 seconds. I need to change the vin number in the second one. I need to know what tool to use and cheapest one because I can not buy an expensive one.
A tool can change/update the ECU vin number using OBDII for JEEP
Hello to all,
I would like to make sw update on Audi A4 B8,5 2013 with VCP and I don't find in by database from Odis.
I need .frf or .sgo 03L906018AC_2841 if someoane have it and could help with it.
Thanks in advance.
Can i make Vmax off?
With Vediamo ?
Thanks my friends
hi i got e60 2008 tried to retrofit driver seat to comfort
after replacing i can move seat from inpa but the seat dont work from seat switches
i know that seat switches module need to have 12v+ and- and k line
can someone please help how to fix it
hi mate jeep Grand chroke 2014 need dash km change orig km 96662 need change 6662 km please help me eprom 93c86
Hi.guis need help with Clio4 airbag crash.Control unit A2C80613911 985101389R--A.SPC560P50L3.Read data flash with J-Link.Thanks
ECU Bosch 026120823 SW 1037370911
I need cut this errors:
hi im new to the forum, just wondering if there is anyway to get pincode for a 2016 dodge challenger prox. i am using skp 900
I did a head gasket on a volvo s40 t5 and one of the guys got theparts mixed up with other part now i have a extra part that im not sure if it belongs on the car or not can someone please tell me if they know where this belongs. [img][/img]
Hi, this is my first post. I have to remove Audi q7 bose component protection. But I am unsure that I know how
I have Abrites comander and Xprog. For Abrites I need Dump file.
I dont have Dump file, how can I read it from my protected amplif? How can I know if Abrites generates good or bad file, and should I only read good one, without component protection? (Non component protection bose amplif.eeprom?) Were on the board is correct eeprom which I need to read?
Adding some photos in link: