Are you the publisher? Claim or contact us about this channel

Embed this content in your HTML


Report adult content:

click to rate:

Account: (login)

More Channels


Channel Catalog

Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 1776 | 1777 | (Page 1778) | 1779 | 1780 | .... | 4906 | newer

    0 0
  • 08/07/17--15:04: Volvo s80 2004 wake up error
  • Hi

    tried to read file from Volvo S80 2004 2.4D 131ps but kess v2.34 give wake up error.. somebody had also seen this problem??

    grts Sven

    0 0

    Hello to all,

    ( 2006 range rover 3.0 td ) ( SALLMAMC46A201095 )

    After cluster correction and batery drain car resulting in a non starter / no crank.

    Readed out with sdd gives a vin problem.. try to put the asbuild file but ecu wont accept.

    Tryed also with pa soft. but ecu gives incorrect respons, vin fault,

    In the dash also lighted the tamperdot, reprogrammed chip with tacho 2008, eeprom is Not a 35080 but a 93C86

    Maybe someone has a solution,

    Thanks in advance

    And the file. ( done with galetto )
    Range rover.rar
    File Type: .rar
    Downloaded: 3 times
    Size: 126.63 KB

    0 0
  • 08/07/17--15:13: m7.9.8 fg galletto
  • Hi
    I need help
    How read kefico m7.9.8 MG7.9.8 fg galletto Boot Mode
    manual transmission
    automatic transmission

    File Type: .jpg
    Downloaded: 5 times
    Size: 79.22 KB

    0 0
  • 08/07/17--15:18: DTC off me7.1.1 rs6
  • Hello!

    Cought someone please disable P1122 and P1118. I remove the secondary lambdas and these faults i cant delete. Thank you.

    Best regards.

    WinOLS (Audi RS6 (v2) - 366304).rar
    File Type: .rar
    Downloaded: 3 times
    Size: 312.46 KB

    0 0
  • 08/07/17--15:27: Passat B6 5D Operations SW
  • Hello all,

    I have recently update my passat 3C the CAN geteway.

    But i have an issue with Keypad from premium telephone kit.

    Address 5D: Operations
    Part No SW: 3C0 035 151 C HW: 3C0 035 151 C

    HW Revision 11 SW 0018

    Does anyone have the SW 0019 or any newer version or solution to fix the battery drain caused by this numpad.


    0 0

    Hi Guys,
    I have made a new thread as I uploaded a faulty file.
    Can somebody please help me with files to make the odometer around 135,000 km.

    File Type: .rar
    Downloaded: 2 times
    Size: 199 bytes

    0 0

    Hey guys my Galletto died and corrupted the original and 2nd hand ECU dumps. Need a good dump from both MCUs as i don't know exactly which side is corrupted. 1087 533
    It's a 2009 M3 with DSG.
    Thanks for the help.

    0 0
  • 08/07/17--15:47: Allison Doc 2017
  • Has anyone experienced communication problems with allison doc 2017?
    I have it installed on 2 laptops and its like they will connect when they want to
    Jpro and the OEM engine software connect with no problems

    0 0

    Hello All,
    I need help activating SIS 2015(2011B) I was looking for the activator which i found it here but somehow i miss the page which i am still trying to find can any one please help me with the activator and instructions how to use it.

    0 0
  • 08/07/17--16:08: CAN Lines
  • Need some help to figure out the two CAN line (Low and High) from this Bosch ECU with TC1762 Tricore

    File Type: .rar
    Downloaded: 1 times
    Size: 509.86 KB

    0 0
  • 08/07/17--16:22: cat c15 on Freightliner
  • need an ecm replacement for a
    freightliner vin 1FUJBBAV97LV92391

    specs cat MXS C15 Eaton fuller Autoshift 10 speed correctly

    please need to know configurationfor vehicle speed my ecm is not reading but my tcm and ecu are reading.

    0 0
  • 08/07/17--16:24: IMMO OFF MED17.5.2


    med17.5.2 jetta.rar
    File Type: .rar
    Downloaded: 0 times
    Size: 1.73 MB

    0 0

    Hello all

    I just bought EasyDiag yellow one , I downloaded eobd 22.51

    Can I make it work with full cracked old files or I have to wait cracked version for 22.51 ???


    Sent from my iPhone using Tapatalk

    0 0

    hi thanks everyone for your efforts in this wonderful forum.Tup

    i am new on this and i wanna find the right information in this topic

    can you tell about some professional forum like this but only for ecu´s professionals?

    can you share with me some tutorials about ecu flashing?

    0 0
  • 08/07/17--18:01: help ptt 2.05
  • was hoping someone could help with 2.05. I was just installed and would connect to Mack trucks with nexiq 2 clone, but it would not perform any tests or calibrations. i asked the person who installed it and he said it probably will not work on Mack trucks only Vovlo. I could understand if i were programming but I am only trying to use the diagnostic functions. So i have now tried with a dearborn dpa5 but it wont connect at all, and is brand new with current updates. Any help would by helpful. this is the second attempt at purchasing a working PTT and it will work correctly.

    0 0

    Looking for a wiring diagram or the pin-outs for the ecu , want to setup a bench top ecu tester to teach kids about engine diagnostics . I have a ecu out of a 2005 hilux , need to know what wires run to the Obd2 port from the ecu, been look for days and the colours dont match with what i have found .

    ECU Denso 89661-0k140

    Any help would be great

    0 0

    Fing20 Im Having problems with cat ET and SIS on same laptop , Having this with both 2016 and 2017 .I can install ether ET or SIS and they work .
    When I install the outer I loose ET . I have win 7 pro 64 , I have formatted HD Clean install & same thing. I have bought 2016 kg from bruschino1978 and sis & can not get them to work.
    We tried everything bruschino1978 teamview with me & no luck . So I bought the 2017 kg at different place & same thing Fing20 Does anybody here have them both running on win 7 -64 ? I have tried on 2 different laptop CF-31 with clean Hard drives . Anyone have any idea on this ?
    Thank you

    0 0
  • 08/07/17--20:02: Detroit DLink 8.04
  • Suddenly getting
    Server connection requirement has been exceeded

    at start-up. Anyone know a workaround? I reinstalled and still same error.

    0 0


    Hot sales from Xcar360!!

    MicroPOD II function:
    1. It can be used as diagnostic and programming tool by the dealerships. It replaces your StarMobile, StarScan, and wi-TECH POD, and enables your technicians to increase their productivity and provide world-class diagnostic services to your customers.
    2. A separate Tech Authority Subscription is required to access to Module Re-Flash Programming, TSBs, wiring diagrams, and repair information.

    wiTECH MicroPod 2 Diagnostic Tool Highlights:
    1. Software Version: V17.03.01
    2. Multi-Languages available: English, French, Spanish, German, Italian, Russian, Japanese, Korean and Chinese
    3. PC-Based: Requires PC connection

    Using Tips (Important):
    Have to connect to network when you use the device.
    MicroPOD II model year coverage:
    Although small in stature, this dongle-style device offers 100% CAN - equipped coverage to 2016 for Chrysler, Dodge, Jeep, and Fiat vehicle platforms.
    MicroPOD II features:

    1.Supports all the latest technologies and vehicle platforms including the latest Chrysler and Fiat Vehicles.
    2.Works as a direct replacement for the wiTECH POD

    For price:PM PM PM me.(To speaks 3 times of important thing.)

    whatsapp: +86 18520783262
    qq : 259024065
    skype : kernchan

    File Type: .jpg
    Downloaded: 2 times
    Size: 53.25 KB

    0 0



    I wonder how to do it Change the number of turn signals.


older | 1 | .... | 1776 | 1777 | (Page 1778) | 1779 | 1780 | .... | 4906 | newer