Hello any one helpme
i search this maps
or full cla error class Kp file
i have 551f damos but not succes compare this section
now this 2 dtc have
17931 - Crash Signal from Airbag Controller
P1523 - 35-00 - Implausible Signal
18058 - Powertrain Data Bus
P1650 - 35-00 - Missing Message from Instrument Cluster
thanks for help
kenwood ddx4016bt please dump reset security code, security code
looking for mpps anyone selling one?
hello guys..this car is in big trouble..customer told me that few times there was some note on disp.like :vehicle security not acesible!! but now car is completly dead..nothing work only ceiling light and hazard flasher do...there is no ignition..key completly dead..steering whell locked.no diagnostic posible.found blown fuse in engine fuse box 20A change it still the same..also fuse 32 on bsi is OK..anybody have schematic of conector on this ELV (steering lock)
BSI looks like punto..so my start will be search for elearn cd for this car but in meantime can somebody help with some shortcuts..
key data are stored in ELV or in key reader ? but IF key is dead I belive that still diagnosis sesion will be posible with some modules at least with key reader?
where to start ?
thanks for all usefull info
I need pinout for tractor New Holland ecu to read with galleto. Thank you.
EDC7 ecu from New Holland Iveco
have tuned it with adblue off about 2 years ago, now dealer has had it and adblue system has faults, need to retune it, our cable is working fine but through the 9 pin connector we get wake up error on ecu and have no communication. I know it isn't the Kess as we are able to read and write a whole other range of cars and tractors in the meantime, it is only this one tractor giving the wake up error.
To eliminate whatever the communication issue is on the tractor we want to program ecu on bench but I would like to do that with Kess instead of needing to do it BDM with Ktag as I do not have the positioning frame and related materials, i found this data on another forum:
EDC7 you can read over k-line.
k-line in pin 31
key switch power is 39
battery positive is 1,7,12, and 13
battery negative is 3,9,14, and 15
you only need one of the battery positive and negative; they are all connected inside.
I am wondering if anyone can help me on it, my questions are:
Can i do this making a connetion from the 9 pin connector with my own wires or do I need to use the tricore harness or an adapter of some kind?
If I can do this from my 9 pin harness or from a regular OBD harness can someone advise the pinouts from these for the kline, battery positive and negative and keyswitch power?
i have a harness that comes with the kess i have never used, it is a small black box, with battery power leads, a switch and then several wires, i wondered if this was just a universal wiring harness for on the bench or maybe it is only for tricore or something? possibly i just need to know what wires correspond with the kline communication and can use this harness?
I have to passat 2011 with parking brake switch the parking brake is blinking on the dash I check with vcds give me error that is not coded, I put the code after accept it give me new error parking brake switch electrical error . I guess the problem with switch but I saw workshops solve the problem without changing the switch, any help .
Renault 8200 294 976-A TRW 50300685LHD 24cl16 eeprom def002 fault reset please.
I need picode from file renault laguna3 2008 keyles go
I read the file with vvdi prog 1L15y chip model
thank you very much
I need help to remove EGR from W168 1.7 CDI 2004.
It's edc15c5 1.7CDI 90HP 0281011151.
Swiftec solution doesn't works. Thanks for any help.
as the subject says, I need the 2008-2017 LC 200 factory service manual, all the threads I have searched regarding this on the forum have been to no avail, pls help
Does any ome use this any feedback? Any issues to be aware of?
Hey guys my computer crashed with my pin code calc on it. I really need a pin for an 2006 Nissan to finish a job Im in the middle of.
I need a pin for D9B53
THANKS IN ADVANCE.
Hi can anyone please help me with wiring diagram or any info on a Porsche boxter 987 2006 2.7 , Engine Code M96/25
Roof control module ( or as they call it a Rear control module located under passenger seat
Its had water damage and Im trying trying to repair it. Any pin outs or wiring info on this module much Appreciated , Thanks
I have dsg kcw the fitted software is 44G but the software size is 400kb I noticed that the megatronic is have software 52 with size 700k , is it possible to flash 44g on this megatronic.
Sorry to ask a silly question, I have had this ECU read and EGR/DPF delete read with FVDI fitted to the car all ok and car runs.... the car wouldn't start in the morning ??
written the original flash back and car starts....
written the MOD.file back no star and P1603 and P1604 error
whilst writing the original file back this time with FGtech I accidently short the power wire (don't ask ) school boy error.
Now ECU still wont start and only fault P1603
I thought maybe FGtech corrects CHKSUM ?
I have original file and flash and a replacement USED ECU can I immo off a used ECU ?? ill put up the files now.
For sale brand new ONLY ONE SET . China , but good one . Brand new.
FVDI 2016 ( 2015 ) Abrites commander. All brands .
NEW , tested on car . work fine .
Shipping from Europe via UPS express insured .
Price 340 GBP + 15 GBP Worldwide shipping express UPS fully insured.
1.VAG - VW, Audi, Seat, Skoda: V24.0;
7.Fiat/Alfa/Lancia: V5.7 ;
10.Hyundai/KIA: V2.1 ;
12.TAG Key Tool: V6.2;
15.Chrysler, Dodge and Jeep: V3.3;
18.Bikes, Snowmobiles and Water scooters: V1.2;
19.HONDA HDS 3.016
21.JAGUAR/ LANDROVER JLR.SDD V145.00
Attached post is too funny
I search for the driver wish map on winols. i can't find it.
I wanna tune the gas-pedal. can you help me, where to find it?
it is missing?! maybe another tag in software as 'driver wish map'?
hi I get the error SCN online VPO GENERATE -12 xentri 03/2017
I did replace the files but the error persists