I'm new here so hello to all.
I don't normally seek the internet for help but with this issue I'm completely puzzled and confused.
I hit my Peugeot 206 a day before xmas, I repaired the body work but airbag light was on ( think this was due to the pre tensioners - I have changed them ) I tried to remove these faults with pp2000 and snap on diag, both failed due to crash data being on my airbag ECU. So i sent this unit away to erase the crash data, I received it back and now pp2000 reads Airbag Control unit Permanent fault - seller claims what he does cannot harm this box, Is this true? Can this be undone and fixed? anyway I do have carprog but no software for it, Is there a way I can get the data from my Airbag ECU and one of you guys and have a look? or is it possible to reprogram another airbag ecu? I can't find any with the exact part number as mine ( I think mine is rare as hell ). I did try another, it reads it but comes up with configuration fault.
I am really sorry for these questions but I'm completely stuck...
I have a problem with an Blaupunkt RCD Navi with Touchscreen on a Ford Mondeo 2009
The unit displays nothing on screen, but random starts radio, with no display, only for a few minutes, stops by himself, and in the morning, overnight, i found it playing radio ...
The unit has been checked, seems no fuse or other electrical damage..
I found something about a TSB, seems it needs a software disc?
Please, any ideas about that?
Thanks a lot.
I have an issue in my system that I’d like to fix if possible. I am using Comand MCS II with DVD 2012 maps. It is working OK for a short use (1-2 hours). However, if it is more than 4 hours the GPS system stalls. I can see a map on the monitor but not directions are given anymore and arrow stays I one place. Sometime, initialization is running. I need to turn off the Comand unit and wait for a while and then it can be used again for a short time. I am wondering what this can be and how it is possible to fix.
Thank you in advance.
Hi, I was hoping somebody could shed some light on how to read a motorolla MCU MC68HC11 KS2 (0H95B). I connected using UPA USB 1.3v according to the UPA manual (page 29). I have shorted the oscillator and lifted RX, TX and reset pins. I am getting error "Reset High Error". Can someone offer advice?
I need to check if the CEM are stored keys. Car will not start the starter does not turn and key error.
Can anyone help in sync immo?
Hi boys can some one give me advice . I tried to update TCM on 2010 1.8 L petrol Cruze and Now have error message E2700 GMLAN_18_1 basicly its gone from 6 speed auto to 5 speed manual . Does any one know how to recover it . I have Genuine MDI + tis to web . Thanks in Advance
could someone correct this dump for 98k miles not km
Any users of WindRiver ICE SX here?
Need 25c160 eprom dump from working cng ecu metatron 6A0 for Punto 1.2
thank you in advance!
Hello I have an ecu for a 2003 w203 c180 kompressor, I would kindly.like to ask you if upa-usb can read the flash so that I can make it virgin.
I need CD travel PIlot 2013/14 with map Italy
I change milage in fabia 2 (2010 gasoline 1.2) by digiprog v4.92 clone yanhua . After programing I have statement on dash : FEHLER : and VCDS shows dtc in dash : general checksum failure. I don't have ori file :/
This dash is Johnson Controls 5j0920800h.
any idea to handle this? any help please?
can anyone tell me where to find the function to disable the "Comfort-Blinker" (you push one time and the blinker goes three times) in Lexia or DiagBox?
Can't find it.
Its an Citroen C4 Pic, Year 2010.
Thanks in advance
Can someone give me a MUT-3 software which work without VCI?
Can anyone help me with a MOST optical sensor
many many thanks
Need solution for radio Delphi F199 sm2 mp3 disable cancheck
Hi can anyone please help me with EURORICAMBI TRUCKS COMMERCIALS SPARE PARTS CATALOGUE software. Thank you
Hi all,someone knows who is doing remap not so expensive?Thanks