Hi. Can someone clear crash for me. Please
My car prog will not do it. 0285010141
Warm greetings to all
my question is that diesel diagnosis interface you recommend me to scan multi that is efficient, thanks to all the q can help me choose
Hello! send the program by e-mail pays for Western Union
Price: 100 USD
versions: 3.2 or 3.5
I have an ECU 028906021af a Golf3 tdi 1z, if I set the ECU with a map of a seat ibiza afn it works on afn?
I recently bought a clone Nissan Consult 3 Plus diagnostic head. I currently own a genuine Consult 3 and CF-19. So I installed the C3 plus software on the CF-19 and hooked up the diagnostic head. Everything connects fine, it scans vehicles. But when I go to update a module, for example today I tried a 2001 Infiniti QX4, it gets through the programming screens up to where it wants to load the file onto the VI. At that time, it says "Transferring from Consult to VI" and sits at 30% immediately. It never moves from here. Never transfers and never updates the module.
Any suggestions? Could I have a bad diagnostic head? I have tried wired and wireless with the same results.
Need electrical diagram for Citroen c2 2004 1.4 hdi please
i need radio code for Grande Punto
radio blaupunkt fiat
Made in Portugal
Fiat 199 MP3 SB05 small 2 graphite
FIAT 735 481 300 0
BP nr 7 648 543 316
Please help me
someone can help EGR off and tuned file for Ford focus 1.6tdci 2006
Thanks for help
I'm trying to re flash my brabus sam unit after a failed update.
I'm using an xprog-m china clone V5.3 with dongle.
I have located the connections on the pcb.
I keep getting the same error no matter if i try to read or write to the chip.
"XPROG vpp pin overloaded. Check VPP pin connection"
I have tried all the Motorola HC(S)12 devices that list the mc9s12dg256 2K79X.
I'm not sure if it is something i'm not doing or if the xprog itself has a fault.
Any help would be appreciated.
I'm trying to remove/delete an unknown password in a used n14 ecm but every time I try the progress bar gets to 13% and then I get an error 26110.
If anyone has a solution to this I would love to know it....thanks.
Anyone fancy tuning this file?
A bit more poke, will do nicely..
I have a working copy of the above, if you want it, pm me your email address and ill send it over.
i need to tuning this file , this is original file but this car has black smoke and i need to remove smoke and to added some horses power, please help me
Does anyone have telematics dvd/cd
Can someone help me with a connectivity problem with my nexiq usb link and my cat et software. I am using windows 7 professional and when I try to connect I this message:
RP1210 Compliant Device - Communications Adapter Error
RP1210 error code: 261
I have this software on another computer and it doesn't give me any problems.
I run the following clones:
on some others
On a daily basis we do the following
Some key coding
Airbag data reset
I have been looking at the genuine Abrites AVDI but once added up it can get expensive.
The basic package at the moment they are offering the TagKey programmer with as a deal for £999.
Can anyone comment on the basic package and what it will do. I need to know what the basic package is i can get away with. The "add ons" are very expensive.
Hi guys i have a problem with Jeep Cherokee 2003, the last key is lost .Need immo off please. ECU :BOSCH 0 281 010 291 with 95p08 c3 eprom.
p/N p56041 700BE
International truck with Cummins ISX CM870 and Eaton UltraShift DM2 automatic transmission.
On the tail of transmission installed two 2-pin Speed Sensors.
If press the accelerator pedal (truck is stationary) velocity signal (vehicle speed) sometimes jumps to 10 to 30 km / h.
This creates some inconvenience and problems:
- While driving may be self-off cruise control;
- While parked may be self-off PTO mode; 3-minute shutdown of the engine is activated and the engine stalls;
- It is impossible to perform tests while the engine is running, such as a test of EGR valve and turbine ...
In the features and options - the option of VSS settings - sensor type was set : Magnetic
Disconnect one or other speed sensor (tail of transmission) - forced the problem go out ... But systems partially not runs ...
In the features and options - the option of VSS settings - sensor type was set : Datalink - Tailshaft - and problem was solved )))
Please comment - why is this happening ...
EDIT #1 : added eng and trn type, thanks machoman777
hi can anyone help my golf traction control light comes on after ten minutes doesnt mater if your moving or no i have read its down to te alternater its charging at 14.3 and does change when the ligh comes on can anyone help ?
hi does anyone do map packs on here ?