HIi to all
i've bipper 2013 with ecu edc16c34 and bsi delphi(see photo of bsi)
the 95160 was changed by someone i think it losted the code key
i'm asking now how to read this bsi because the car start but not over
hi pls can someone help with this problem on GLK 4MATIC 350 2010. (P0087 FUEL PRESSURE LOW). and vehicle misfires anytime this dtc comes but work normal when refuel the car even if the fuel is upto quarter tank. is this a false flag from the fuel ecm or fuel pump or any order one.
Hello MHHAUTO members.
I have a customer with a 2012 Fuso Frighter and the engine warning light flashes continuously when ignition switch is turned on and when the engine is running. Used the Star tool to check for codes but it does not want to communicate with ECU. Tried the PS2 tool but same problem does not want to connect. Advise will be appreciated. All the fuses are ok.
Have a weird problem with sl500 03. Have a current code in esp module about esp communication with ecu. When I access the fault code it sais to process fault codes in ecu first. Ecu has no error codes. So what in the world. I replaced with other esp module, other ecu and other sbc. No change. Also checked the can bus lines that go in the driver foot well.. seems ok.
I am having an issue with my Cat Factory Pass generator by Sultan on a new machine. Every other machine that I have has this program running without an issue but this new one will not run it. I am getting the little red light at the bottom as seen in the picture in this post. When you try to make passwords it just hangs for a sec and then comes back with nothing in the password blanks.
I believe that I read something on the thread where I downloaded this a very long time ago but I cannot for the life of me remember where the dang thread is or what was said about it. I need help quick; please and thank you!
I did not receive the .dll error when I first tried this on the new machine so I never ran the patch. Upon discovery of the problem, I ran the patch to see if it would help but no results. I have tried replacing the .dll's in question and that had no result as well. I also unpacked the .rar and installed a second time, again with no result.
I am at wits end with this and I know I will be needing it tomorrow. Any advice will be appreciated greatly, as always.
I am in search of a High Interlock password generator for Caterpillar engines. I know a few people on the forum have it as there are threads where people are getting the high interlock factory passwords. I have tried searching for it but these threads are all I find. If anybody has it or knows where I can get it, please reply or PM me with the info.
I have got this problem, which is :
when press power button ,the radio start slowley with the flag of Skoda for 10 seconds then stop alone ( switch off ),
Here is scan,,, any help ?
Need it new software? or need update software?
I wanted to know if somebody could tell me the difference between the three versions of Detroit Diesel. I was guessing the 6.5 is for pre 2004 trucks, 8.0 is for 2012+ trucks, and 7.1 for everything in between?
Tried to read Peugeot 2012/3008 ecu:siemens.SID807 EVO via described on Ktag/BDM fam 320 with external battery power..It showed "Communication error.pls check power connection-0X100B" than car did not start even cranked..we did try again even it was not connected how did it break the ECU ?..Besides we done that car last year with no problem however it went to dealer and upgraded the sw and come to us for remap..
Another friend of mine had the same problem with FOMOCO sid807 2 days ago and he is awaiting for help too...
What changed on Ktag or ECU that It happened like that and I cant do anything with ECU what I just tuned a year ago ? How factory upgrade made that changes ?
PLEASE URGENT HELP HOW CAN I FIX THAT ?
the next 12.2014-01.2015 version is almost finished I was busy adding many improvement. In this edition it is optimized to ne used for c4 sdconnect. C3 is easy to reconfigure, so there will be only minimal disadvantage comparing to c4 users who have it more difficult. Now sdconnect can connected via infrastructure mode (wlan over router) as same as easy as ad-hoc mode (direct mux-pc wlan).
I still need some testers before making it public. Please pm me, and give your skype name. Thanks
some new improvements:
-smaller vhd system size 3.1GB
-all DBs are external (even Xentry and DAS)
-new sdconnect tool kit added
-addons upto 4260
-addons are now addable.
-different DBs with different content to give more choice to download (e.g. Xentry OnlyCars)
-Fully system files optimized (Speed and directory optimized defrag)
-All pictures are recomprimized to save space and accelerate the system.
-and much more
This is the next edition of the unique native running Universal Xentry/DAS System without needing any pc virtualization.
It is a portable system with lot of MB stuff. A Windows XP based system installed in VHD-File, which can be located everywhere (USB or Harddisk) and being booted and run natively by a bootloader (on a USB-Stick, local harddisk or CD). So no change to the running system and without the need for any virtual pcs.
with the Bootloader+VHD+DBs methode:
+No need for to make any change on the laptop you will use. Even you dont need to have a harddisk in the laptop.
+No need for seperate harddisks for each diagnosis System.
+No need to be worried if the laptop has a irreparable software or hardware error, and it will not run.
+No need to split your harddisk to many annoying partitions.
+No need to mixup your harddisk with many Windows versions.
+No need to waste ununsed space on each system, when you can place data on a common partiton.
+No need to be worried about having any unwanted changes to the diagnosis system from someone else, as it has build in protect sandbox-functions.
+No need to fear from ruining your laptop system when removing or replacing the diagnosis system.
+No need for big harddisk storage for huge vmware files, when you only need to have DAS/Xentry (29GB)
+No need for virtual PCs anymore!
+No need for powerful cpus anymore!
+No need for driver configurations at host system anymore!
This system has 3 parts: - Bootloader: This needed to get the base system loaded and run. It will scan all partitions for the vhd file and load it from where it is found. - VHD-file: This is the base system, where Windows XP with MB software are in. - DB-files: These are the DB files for the MB software as WIS, EPC, Sdmedia... have not to be on same drive as Bootloader or VHD.
Once Xentry/Das system booted, you can add your hardware specific drivers, if there any missing. I integrated more than 1,5GB of drivers. Before doing anyting new, restart the system 2 times as the first boot will detect changed hardware (takes time), and the seconds installs it. See the folder "may needed" on the desktop, if you have non-working drivers in device manager. It is optional to install all drivers. You need only to have get your USB-rs232-adapter running if you use c3, or LAN-driver if you have SDconnect.
The keys (Xentry/DAS/WIS/EPC) are hardware related, so you will need to insert new keys each time you use this system with new hardware. (see may needed folder)
You can use this system on real PC or in a virtual PC. I prefer to use on real PC where it works at fastest and portable.
For real PC you need (new method): 1. A boot device to install and run the bootloader e.g.:
- Your internal harddisk of your PC
- CD/DVD-Drive (bootloader placed on CD/DVd iso) 2. for the VHD-file: you have to place it in ONE-PART (contiguous) on root of a writable drive, this can be:
- internal HDD (fastest)
- USB-Drive (Some old USB-Sticks are really slow and may cause bad system performance) 3. for DB (optional): they have to be placed it on root of a drive, no need to be contiguous, this can be:
- Your internal harddisk of your PC.
- USB-Drive (Some old USB-Sticks are really slow and may cause bad system performance)
- burned to a DVD/BR
For Virtual Machine you need (old method):
1. for the VHD-file: you have to add as first IDE virtual harddisk file.
2. for DB: they have to place it on root of second IDE virtual harddisk file or any real drive connected to the virtual machine.
3. You must configure your virtual machine com-port.
-If you want only Xentry/DAS and not WIS-EPC-SDmedia ... : then you need only to download Xentry/DAS DBs files. -If you get bluescreen with 0x0000007B error and no error file: in the windows boot screen (where at with the 3 seconds delay is) try to select other HAL. Old celerons for example are single core CPUs adn may cause this error by default the setting for multi-core CPU is active. Test also other options if this not not worked, one of them may still work. -If your PC hangs while loading Windows animation (or on black or blue screen) and you have the VHD on the internal harddisk: you may have the AHCI issue of SATA drives. Windows XP has no direct SATA support and this causes this hang. To fix this you may change your BIOS setting. Try searching after SATA Configuration or On chip SATA. Select Legacy IDE or Native IDE instead of AHCI. Windows XP doesn't have all drivers to recognize AHCI, so disable it . I installed several AHCI drivers in the system and my laptop with intel chip is working in AHCI mode. Please share on which Hardware it worked with deactivated AHCI, and on which with active AHCI (an AHCI device is active in device Manager). In Native native IDE mode, the SATA controller looks and acts like a standard ATA controller that the basic driver will recognize. If not worked then place vhd on usb-drive.
-if you have black-screen at bootloader, no boot media found when selecting boot media or windows 8 boots directly: then disable UEFI if active. deactivate: Secure Boot, deactivate: Fast Boot, activate: CSM (Legacy Mode insted of UEFI). If it is not posible, use MBR-BIOS-boot anabled PC. Updating BIOS may help, as some MBs have a non working lagacy-boot mode. To enter UEFI from Windows 8/8.1 see: http://www.youtube.com/watch?v=gDcf3Ow6XjY
-If you get a blue screen when you boot and get 0x0000007E "WDFLDR.SYS" error: then rename this file in c:\windows\system32\drivers. Dont blame me, blame MS. You can mount vhd in windows 7/8 or use a vhd mounter program. (I allready applied intelppm-fix to prevent blue screen caused by chaging between AMD and Intel CPUs)
-Communication problem: The most problem can be the used USB-rs232 adapter. I use my own programmed adapter for that, which works great! PL-based adapters doesnt work good.
The system content:
Universal AIO MB LiveDiagSys - v2015.02.15 - disinfetor
+ DAS/Xentry 12.2014-01.2015 + Offline ECP PL69 1.2015 En + PDF Printer added + "Open file location" menu
+ all addons (till 4260) + Missing pictures Xentry + reset for sdconnect + Blacklist fix
+ Smaller partitions/vhd + IE restrictions removed + antivirus removed + Startup fix
+ Offline programming fix + Internet filter removed + No Low space alert + Standby disabled
+ tomcat7 shutdown fixed + prototype 212,207,... fixed + Acrobat Reader 7.0.9 + Standalone DAS
+ BG update service disabled + Star pass: User$star2004 + MFT and FS optimized + DAS languages
2. AIO MB LiveDiagSys VHD-File
3. ExternalFiles: + DAS/Xentry 12.2014-01.2015 Cars Only DB
+ Vediamo v5.00.05: no free keys + Vediamo v4.02.02: com2 set
+ Vediamo small CBF-Only-DB (609MB 1080 unique CBF files) Helper Edition:
1. Bootloader + Bootloader CD
2. AIO MB LiveDiagSys VHD-File
3. ExternalFiles: + DAS/Xentry 12.2014-01.2015 Cars Only + Full DBs
+ Vediamo v5.00.05: 3 free keys + Vediamo v4.02.02: com2 set
+ Vediamo full CBF-Only-DB (2.7GB 3952 unique CBF files) Gold Edition:
1. Bootloader + Bootloader CD
2. AIO MB LiveDiagSys VHD-File
3. ExternalFiles: + DAS/Xentry 12.2014-01.2015 Cars Only + Full DBs
+ Vediamo v5.00.05: 5 free keys + Vediamo v4.02.02: com2 set
+ Vediamo mega DB (over 20GB 15000 CBF,CFF,smr-d and VSB files)
+ WIS 11.2014 DBs + EPC 11.2014 DBs: Prices PL69 1.2015
+ SDmedia v01.2014 + Starfinder 2010 + Disassemby Assistant 2003
+ Vintage MB Repair Info + Technical & Training Info library (disinfetor ed.)
Changes since 09-2014 Ed:
-New system made from zero (not an update)
-EPC-WIS: Datacard enabled
-Xentry: internal EPC/WIS linking added
-new speed optimized file compression method used
-Vintage Mercedes-Benz Repair Info Library (unique)
-Mercedes-Benz Technical & Training Info library (unique)
only none-leechers will get the full version!
If you had previous version from me, you will get password for files only:
-if you wrote a review about the version you got.
-if you an active helping member in the forum, with many new posts/threads.
(a short comment, thanking or asking for someting is not enough)
else you are downgraded to leecher-status, even you have been donated before.
Donating is a sign to give that you are not a leecher, so please be act so. I dont sell here my effort , I give it only to the people who also help others! Else you will get only the limited slimmed base version.
Some videos (shown is 7-2014 but the 1-2015 is similar)
If you want this harddisk please contact me on pm!
I need help to fix the following:
1. Booting from USB 3.0 port of my PC works. File transfer speed ist USB 3.0, but the whole system is too slow, when I use a USB-Stick (not on HDD).
2. Enable to boot as efi.
3. Fix the ehci-sata boot problem.
IMPORTANT: Dont ask me for support on PM. Write your problem here! Password on pm. Dont forget to support by giving thank, a rep and rating! I have many posts, so you must tell me for which post you are asking the password for!
I share here my pm responce to a leecher, which applies also to all leechers: With the donated money I pay my internet costs (mostly for premium accounts) and for devoloping car-Hardware. Anything left from this money goes to a local gevornment-approved charity organisation. I have no car service and I earn no money from fixing cars like you and most others in the forum. Only for private use, for my own car and friend's cars. As it my hobby and not my job I do it for free of course.
Suggested 10€ is not that much money if you had not only you spent your countless time for it, but also alot of money to get it working. In this year alone I gave around 2500€ for car tools, which I really never need or musthave to buy as most people here in the forum, and again: I dont have car service or similar, so I can make money to finance it, as you can.
I love to share my experience with others, and hope to contiunue and improve this by financing a part of. By your support, I get motivated to make better work. And blieve me, you will profit from it way more than me.
I spent and will continue to spend my time and give my work with love for all people who also spent thier time for helping others. In the previous projects I begged everyone, who downloaded the SW to share their experience, to make it better. Anyone commented, gets the new edition. However, you was one of the leechers, who downloaded and even used it successfully, but never shared anything, even saying it worked. An unfair commercial project: Misuse other peoples effort to make money in your garage without helping back the people who made your profit possible. I spend weeks for it, but you have no 5 minutes from your precious time to write even a small comment. Meanwile you have the time for complaining I didnt give you the next edition.
In the forum you have only 3 posts, where you only asked others for help. So please be fair, and think again who is guy with a commercial project here.
If this edition is the same as DXEWS Edition, then please tell me for what did I spent my time in the past 5 weeks (sum of atleast 150h)? You can see the change list of DXVEWSSd14Sf08Da03 Edition and compare it with DXEWS, if you still think it are the same.
My english is not good, but I know how to write and spell disinfector, which is by the way not my nickname.