Are you the publisher? Claim or contact us about this channel

Embed this content in your HTML


Report adult content:

click to rate:

Account: (login)

More Channels


Channel Catalog

Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 4748 | 4749 | (Page 4750) | 4751 | 4752 | .... | 5081 | newer

    0 0

    Dear folks, 

    Find enclosed the Xentry Diagnostics OpenShell 12 2019 32bit installation fix.

    Password: Known by active members.

    Best regards.


    XDOS 12 2019 32bit fix.txt

    82 bytes

    0 0
  • 11/04/19--00:44: Vediamo flash CDID3 UNIT
  • Hello. I want have managed to flash a w212 m651 cdid3 engine control unit using vediamo. I have original codes and original diagnostic. I habe tried to do initial start up of the unit after the flashing but the procedure goes to 100% and then starts again. Any help? Thank you

    0 0


    Any one ever fixed a chrome Mercedes Smart Key which did not send any RF signal?
    IR works fine, car starts and runs fine but Remote Lock/Unlock does not work.

    Checked for RF but does not transmit any thing...

    0 0
  • 11/04/19--00:57: HELP immo Mitsubishi 3000GT
  • need immo off for Mitsubishi 3000GT

    ECU MD190662
    2Z03 M

    thanks all

    0 0
  • 11/04/19--01:09: EDC16U1 Injector rescaling
  • Hello...
    Can anyone rescaling Injectors of VW AXE-Motor with bigger Injectorheads??
    Mounted are 5 hole Heads with 0,219 and the car is very strong smoking.
    Sw is: 378321 (070997016H_7839)


    VW T5 2.rar

    244.91 KB

    0 0
  • 11/04/19--01:28: Bosch ME7.3.2 CAT OFF
  • Hi Guys, 

    Can any offer CAT off solution for ME7.3.2 ecu? 

    Know of any working solution available?

    0 0
  • 11/04/19--01:32: Simtec7.1 p0000 remover
  • Hello friends!

    Auto: VW Golf 5
    Engine: 1.6 BSE gasoline
    ECU: Simtec7.1
    HW: 06a906033NJ
    SW: 5WP40875 CAS71208 9550

    I made euro2 and tun. Error p0000 is present. Can anyone help remove it? For firmware in pm Kolo

    0 0



    0 0

    Somebody have ori file for Scenic 3 1.5 110 hp sid 305..?

    HW: 0037R
    SW: 0386R
    VIN nr.:
    SW ver.:
    HW Ver.:
    SW upg.: 0797R

    Best Regards

    0 0
  • 11/04/19--01:39: BMW 3 DME MSD81.2 pinout
  • Hello
    I need a pin description for the BMW 3 continental DMe MSD81.2 engine driver
    The harness was damaged and another mechanic probably changed pins. The oil temperature sensor is not working properly.

    0 0
  • 11/04/19--01:44: Scania SDP3 2.41.1
  • Dear All ,

    Scania SDP3 2.41.1 + Crack .

    Thanx + rep = Link

    Regards ,


    0 0
  • 11/04/19--02:06: renault clio 4 dash help
  • hello all friends i need flash p and d for dash clio4 i tray to modifiet odometre with renolink but the flash dump is bad and dash stop to working if eny one have good flash p and d with patch sync disable 
    thanks for eny helps

    0 0
  • 11/04/19--02:38: yamaha r1 2016
  • hi can anyone tell me if i can write this file to any 2016 flash inside ecu using ktag 

    reason i ask this is because the file that i have read has all the flash tune add ons including blipper and oxy delete and power tune , my firends want same flash as mine rather than go to flash tune 

    also is there immo data in flash or is it separate inside eeprom 

    thank you


    my bike yamaha r1.rar

    254.91 KB

    0 0
  • 11/04/19--02:44: ODIS SETUP TO USE VAS6154
  • I just got one set used VAS6154. I try to use with ODIS 5.16. But look like the ODIS can not recognize the VAS6154. Anyone know where is the problem. 
    The windows can recognize the  VAS6154 (PLEASE SEE ATTACHED FILE)




    91.88 KB

    0 0

    Hi can some 1 please help me adapt vw polo 2010 ecu with dash i have 93c86 dash and 95320 ecu attachment with ecu pic il realy appreciate it thanks regards[Image: 0c08d31d2e01964ae0bff91b68430cb8.jpg]http://cloud.tapatalk.com/s/5dc0015cc0a2...20road.ziphttp://cloud.tapatalk.com/s/5dc001825136...281%29.zip

    Sent from my SM-J250F using Tapatalk

    0 0
  • 11/04/19--02:58: PSA EDC17C60 DPFOFF PROBLEM
  • HI

    I have problem with dpf removal for peugeot edc17c60 when i write first time mod file on bench with pcmflash car start few times then wont start
    then i write eeprom car starts agian

    then i read dtc (p3028 engine ecu) when dtc is removed from file still same problem car wont start ,when i write orginal file with  car start normal 

    when writing you have to write eeprom agian so the car starts with mod files start few times and org file start ok 

    is this a pcmflash or file problem and when write mod file urea (adative) keeps blinking

    0 0

    Cmd read. 
    Anyone can do right Dpf Egr off?



    44.33 KB

    0 0

    I need good manual solution AdBlue and nox off for Volvo FH4 euro 6.
    Does anyone have?
    Not for free of course Wink

    Wysłane z iPhone za pomocą Tapatalk

    0 0
  • 11/04/19--04:03: keess v2 5.017
  • hi all.need backup sd for kess v2 5.017.red pcb
    my data its formated.

    0 0

    hello friends! 
    maybe someone have a clue about those errors .the car was left with all 4 doors open overnight .


    range rover errors.rar

    87.17 KB

older | 1 | .... | 4748 | 4749 | (Page 4750) | 4751 | 4752 | .... | 5081 | newer