Quantcast
Are you the publisher? Claim or contact us about this channel


Embed this content in your HTML

Search

Report adult content:

click to rate:

Account: (login)

More Channels


Showcase


Channel Catalog



Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 4780 | 4781 | (Page 4782) | 4783 | 4784 | .... | 5073 | newer

    0 0

    MORE INFO IN PM

    0 0
  • 11/11/19--02:36: Ford Travelpilot need code
  • Hi. Need code for Ford Travelpilot 
    C7E3F0925 D 2326394
    7 612 330 925
    BR.

    0 0

    Hi
    I got a ECU from a VW Crafter. It´s a EDC16CP34-4.4 0281014132 074906032BA. I need pictures from the top right corner of the circuit board. See attached pictures. The ECU has been opened before by someone unknown and not sealed at all after that. Now there is a new owner of the car and when he tried to write a new map to the ECU by OBD there was a problem writing to the ECU. So when the lid was lifted off the ECU some capacitors and resistors fell out. He soldered them back but got some of the components in wrong place. Now the ECU is on my bench. So is there anyone that has any good pictures on this PCB so I can figure out how to put the components. 
    /Henrik

    0 0
  • 11/11/19--03:04: need NOX removal
  • Hi,
    see attached ID, fault, binary taken from kess.

    .rar

    Touran 2003.rar

    1
    813.33 KB

    0 0
  • 11/11/19--03:22: VGS SCN CODING
  • Hello need Assistance of Scn coding for new Control unit for VGS
    skype
    danicon94

    0 0

    Hello everyone! Today my friend lost his volvo key. He has another one, būt without immobilizer. How can i solve this problem? I think there is only 2 ways. 1- immo off and 2- try to code. I have only kess, Ktag, vag, delphi and Autel car computers.

    0 0

    Hi,

    I have a problem with an old ZF 5HP Gearbox TCU Unit on an Audi A6 2.7 Biturbo
    The old TCU  with part number 4B0927156CC was broken (no connection possible, car in limp mode).
    I tried to replace it with a used 4B0927156ES
    but the car drives bad and tcu shows fault "ECU-TCU Software incompatible"

    Can someone help me to solve this? How can i get tcu working with the correct Software?



    Thank you very much 

    Regards 
    Marvin

    0 0
  • 11/11/19--04:11: Sprinter w906 2016 nag2
  • Hi dear . Im have new plate to 7g coding from service. Im swap my rear axle with other ratio. Gearbox vgsnag2. Coding new ratio (ar2) for ezs and kombi. Maybe u have info for vgsnag2 coding ratio? Actually coding is ZSS6 from ar1.

    .jpg

    20191111_131056.jpg

    0
    339.5 KB

    0 0

    Hello everyone, I'm looking for a software that would have all the wiring diagram of cars.

    Waiting for an answer. Greetings.

    0 0
  • 11/11/19--04:50: need activate carprog online
  • hello guys
    please can someone help me activate carprog online 8.21?

    name: shmuk
    hw id : 27E86-D08DE-A6006-AB5B9

    thank you

    0 0

    hi all freind i need code pin for peugeot 107 
    2011
    bosch 0261s06148
    89661-0h190

    .rar

    eeprom 95160.rar

    1
    195 bytes

    0 0

    0 281 010 455
    55188111

    .rar

    alfa 147 full bdm.rar

    1
    614.76 KB

    0 0

    HI

    I have a question for those of You who have more experience in immo chip programing .

    Last case of mine.   2006 VW Passat B6 - all key lost 



    First i had to  read  Comfort Module dump by carprog, then VVDI2 to get 7 bytes of CS and PIN. No question about it, then i've tried to make dealer key by carprog  using TP23 chip  (precoded by FVDI2018 and Abrites from ID48 transponder  ) and precode  it by SC 7 bytes.  After that, using both  fvdi2018 and original Abrites tried to add new key by obd2  and the car did not accpet the immo chip. All the time i had information  on dash -     new key programing 0/1 .  

    After scanning immo chip by carprog, i have info that immo chip is - non locked ?  I do not know why, carprog after making Dealer Key is not locking the immo chip ? I guess it should do it to make possibe  adding key by obd2.


    It's good that i have abrites , fvdi and carprog, like that i can compare and try them what they can / can not do. So took another TP23 and precode it by abrites Key tag tool using  dump, then check chip again with carprog, and this time is locked.  There was no problem to program it to the car by obd2, car starts fine. 

    Any idea what carprog can not pre code transponder correctly ?


    Best Regards

    .jpg

    20191106_215844-2656x1494.jpg

    1
    376.62 KB

    .jpg

    20191106_220508-2656x1494.jpg

    1
    435.62 KB

    0 0

    Hi all
    i make BCU from peugeot boxer 2.2hdi 2011 and have damaged p-flash in mcu nec,must read this mcu NEC D70F3631 for repair but no can find on web conecting programmer for this mcu,in vvdiprog is conecting but only on mcu i make picture on BCU pcb if some need use magics buttons,pass pm

    BR asto

    .rar

    BCU Peugeot Boxer conect mcu nec D70F3631 vvdiprog.rar

    0
    1,011.67 KB

    0 0
  • 11/11/19--05:10: SID310 and AVDI!
  • Hi,
    Please, is there someone tried to read and write ecu Continental SID310 by AVDI ABRITES?
    I have tried to read it by obd no problem, as for writing obd is not available, then must make it in boot, for reading and writing has been normally, then I brought it back to the car, here I fell into a problem, the engine doesn't start and no communication with ecu, I tried to pass other read it impossible, aware that The file is good. Is there any solution?
    Maybe, we can solve this problem with another programmer tool, like MAGPro or KTAG?

    Thanks in advance

    0 0

    Pls help Peugeot 607 2.2 dpf egr dts off
    ori file

    .rar

    0281010567-1037353283.rar

    0
    159.69 KB

    0 0

    stage 1/2 tuning and all solutions 

    first file free 

    PLEASE ADD US ON SKYPE FOR FILE SERVICE

    0 0

    Does anyone have this flash file for 7 speed DSG?
    Thanks

    0 0
  • 11/11/19--06:32: Mustang PCM Bootloader
  • Anyone knows where to look for Secondary Bootloader for GR3A-12A650-BTA PCM
    And this software GR3A-14C204-DJA

    Mustang GT 2016 VIN 1FA6P8CF1G5327353

    Im using UCDS and it cant detect correct SBL because PCM is tuned and software number is changed, i want to flash it to stock

    Thanks for help

    0 0

    Need code for BNO881
    Blaupunkt 7 612 002 021
    VW Radio Navigation
    1T0 035 194 A
    VWZ1Z7D4007725

    In attachment is fis dump

    Thank You !

    .zip

    eep fis.zip

    1
    1.66 KB

older | 1 | .... | 4780 | 4781 | (Page 4782) | 4783 | 4784 | .... | 5073 | newer