Are you the publisher? Claim or contact us about this channel

Embed this content in your HTML


Report adult content:

click to rate:

Account: (login)

More Channels


Channel Catalog

Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 4970 | 4971 | (Page 4972) | 4973 | 4974 | .... | 5073 | newer

    0 0

    Hi Guys,

    I unlocked PCR 2.1 from a Touran 2011 with ktag. Then I read the ECU with kess on bench. When clicking id it said "Unlocked" and id worked.

    Then I read it with kess on bench. Worked too.

    I tried to write the modified file with kess on bench to. After 100% it gave an error. Stupid me.

    So I wrote the original file back, which worked fine.

    I can id and read the ECU still on bench. 

    But in the car there is no communication with kess or vcds to the ecu.

    When I make ignition on the fans starts to run and light goes on.

    Any ideas?

    When the ECU is dead, which used ECU can I buy? Which number is important? And who can adapt this ECU?

    Thank you guys.



    157.37 KB

    0 0

    Good day

    I have this Fusion Hybrid as a non starter. The petrol engine does not crank.
    The SOC in the HV battery is 36 percent. Also in Battery control modules there are 3 faults for low voltage and unstable voltage.
    The car had minor front impact.

    Is there a way to charge the HV battery? If I bypass kl.50 would the petrol engine start? 

    Any help is welcome!


    0 0
  • 12/24/19--04:50: Merry Christmas
  • Have a very Marry Christmas everyone 
    Stay safe , enjoy the time with your loved ones and stay marry
    Good things will come
    Big thanks to everyone here that always give a hand to the ones that really need it  bow Anim_19 Fing24
    So many good people here 
    Lots of health   Beer Beer 

    0 0

    Hey ,members please l have renault megane 3 with abs eeprom 95160 on abs 251002 KM please l need 160000 this file from abs 


    ORIGINE FILE ABS MEGAN 3 KM 280....rar

    972 bytes

    0 0
  • 12/24/19--04:55: BMW E71 MEDV 17.2 DTC OFF
  • Need to turn off the following DTC
    MEDV 17.2

    2bd9 fuel rail pressure sensor, electrical; circuit short b+

    0 0
  • 12/24/19--05:11: ME7.5 Crackle map
  • Hello,

    Can someone do me a favour and add a crackle map in this file ? 

    ECU: ME7.5

    Best regards.



    267.69 KB

    0 0
  • 12/24/19--05:14: EDC15C2 Peugeot AGR OFF
  • Can somebody make me AGR OFF and Checksum on this AM29F400BT from a EDC15C2 Peugeot




    170.24 KB

    0 0
  • 12/24/19--05:15: Vovo V50 CEM ECU ABS synchro
  • Hello friends. i need your help, ready to pay ..... ECU is SID807 evo



    5.48 KB

    0 0
  • 12/24/19--05:21: ptt2.7 with inline7 adapter
  • Hello,,

    i have tried to connect ptt2.7 by using inline7 but never success. as i know inline7 made by nexiq which  support ptt moreover it mentioned in inline7  description that support ptt software. the problem is that inline7 never show under connectivity in PTT as not recognize by the software

    is there any solution or just it will not work.

    thanks for any reply.

    0 0
  • 12/24/19--06:15: RDU222.CBF Needed
  • Hi Mates! 
    Looking for RDU222.CBF (SGR radar sensor control unit)
    Thanks in advance!

    0 0

    Kess Master V2 with box (was a slave but modified)
    only work for cars ~till 2016
    Its internetsave but not possible to update without modification

    Software 2.23 Firmware is 5,017

    ECM Titanium and WinOLS 2.24 are inclusive 

    Price is 1.150€ & Laptop is 150€

    pick up in Berlin/Germany would be the best but also sending is possible!

    cincerly Daniel

    [Image: acf8f5-1577197999.jpg]
    [Image: 7c035f-1577198091.jpg]

    0 0

    Hi, I am searching DAMOS file for:

    BOSCH ME7.7.0 
    Bosch nr: 0261S04012
    SW: 1037389086
    999cc N/A 52kw

    attached bin



    296.33 KB

    0 0

    Merry Christmas to all,

    I have in my bench an 262-2879 01  KHX Engine ECM from a Caterpillar 290D EBM00***, every time I connect the ET to  ecm it is in test mode, I terminate the test mode but when reconnect the ecm is again in test mode.

    where am i getting lost?

    0 0
  • 12/24/19--08:55: p003000 GLE 400
  • Hello and merry christmas.
    I have this car mercedes benz gle 400 year 2016 3000 cc gasoline  M276 ENGINE CODE  at the workshop and have this code p003000 it seems that i need to replace the lambda sensor. I want to make sure it is the right one. I looked everywhere and found the it need to be the upper sensor at the right side of the car .
    Thanks in advance

    0 0
  • 12/24/19--08:55: Volvo FM12 Immo code
  • Hi can someone give me the immo code for a Volvo FM12
    Chassis: A568563

    I accidentally overwrite it when flash the vehicle ecu

    0 0

    Scania SDP3 2.42.1 + Keygen Full

    Best Regards

    For Mhh Auto members

    Reputation + thanks = PM for Key decrypter



    116 bytes

    0 0

    Hi guys 

    Want to buy 2019 bmw m2 competition 410HP mevd17.2.g damos. Please download the attachment for comparison.

    If you have very similar please PM me。

    Thank you



    128.09 KB

    0 0
  • 12/24/19--09:24: ZF ASTRONIC
  • Hi got in to 2008 Setra Bus that have Detroit S60,ZF ASTRONIC Transmission
    As I found out "Transoft" that I had does not work with it
    Jpro does not recognizing ether
    True shifter display got 3 active trouble codes
    117 with stop and wrench
    171 with wrench
    192 with wrench
    this bus was parked for 3-4 years
    no one could fixed and they could not tow to shop that can fix problems because rear suspensions was not getting air to raise up
    As per prior history :
    Bus was driven and in the middle of trip developed problem -regeneration could not complete
    the mobile mechanic came out with diagnostic got regeneration done and drove bus to roadside small shop parking lot
    after some while it quit starting they replace starter
    had problems with alternators-replaced
    than the rear drive and tag axles did not raise up -someone diagnosed air leak in transmission actuator clutch -it was replaced
    I did fly to that bus but only had time 1 day to work on it
    So problem with suspension-safety check valve that keeps 60psi in airbags was bad -got it fixed Bus raised up.
    Clutch actuator was replaced prior (probably did not needed)-I also installed original back -it did not leak
    When ingine is started -display shows "CH" and "AL" no warnings untilll air buildup
    When "AL" turns off( "stop "CC" and wrench shows up)
    Air supply to clutch actuator checked -ok
    The check valve in air supply of actuator -ok
    Clutch actuator moves back and forth-rod of actuator original in length
    Performed erase code procedure -same problems!
    I came to conclusion become it was sitting for so long -that problem with clutch itself mechanical problem
    Any advice on farther trouble shooting?
    I found testman diagnostic software-need advice -what interface I can us with it

    0 0
  • 12/24/19--09:34: SIEMENS SID 801A DTC OFF
  • Hi,

    Could Somebody Make DTC OFF P0400

    Citreon Berlingo 2.0HDI RHY

    Thanks Very Much


    29f400bb org.rar

    126.93 KB

    0 0

    Please help figer out why vvdiprog fail to read the peugote 1007 2007 bosch me.7.4.5 ecu i tried with 2 the diagrammes im i doing somthing wrong or must the ecu by power up while reading? Or must the 95320 chip be removed before reading??

    thanks [Image: d96063f21164f5846734e189a3a019b9.jpg][Image: 623019806739dab617aa96f934107a25.jpg][Image: 9937866c048df8559b0e9328ce7d6ec1.jpg]

    Sent from my SM-J250F using Tapatalk

older | 1 | .... | 4970 | 4971 | (Page 4972) | 4973 | 4974 | .... | 5073 | newer