Quantcast
Are you the publisher? Claim or contact us about this channel


Embed this content in your HTML

Search

Report adult content:

click to rate:

Account: (login)

More Channels


Showcase


Channel Catalog



Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 581 | 582 | (Page 583) | 584 | 585 | .... | 4905 | newer

    0 0

    Please, tell me where in the Mercedes G55 99 year is located an infrared module IFZ (FBS2) 2108202726
    Thanks.

    0 0

    Can anybody help me with the dash of Mercedes Atego 816 2005. It shows "Ins 0 1432". Can anyone check the dump 93lc86 if it is correct. Or the errors is into the flash M29W800? Thanks.

    mercedes atego 816.rar
    File Type: .rar
    Downloaded: 2 times
    Size: 520 bytes


    0 0
  • 06/15/15--14:02: Allison calibration
  • Guys!
    Maybe anybody can tell me more about allison calibration files.
    I have a rebuild transmission (gen 3). And as i see last time was changed TID2 thermistor. So i have a problem with code 33-23 'Sump oil temp/ sensor failed high'. I installed 2kOm resistance for this error gone but i need update ECU calibration.
    So i have 2 choice as i understand:
    1 - get right calibration files and reprogram Allison ECU. But where can i get it
    2 - i have a same truck with a proper calibration/ so i need download this calibration and reprogram wrong calibration for another one.

    So how can i do it? And about point 2 . Is it possible to do? I mean use calibration from another truck?

    Thanks

    0 0
  • 06/15/15--14:17: Mercedes W204 NTG4
  • My HDD is dead after try to update, the hdd is not posible to start again, its stuck on the middle,

    i will change with new HDD, but i need image file, or boot file,

    i was try to take the HDD from my friend and make the CLONE, but can not with PC, or i need to know the start procedure....need help

    Thanks

    its IDE 40GB

    0 0

    Hi,
    my install from GT36a is broken.
    now i search for an VMware Image or Files from an actually GlobalTis with SPS and GDS2 Support.

    I hope you can help me.

    greets Jupp Smile

    0 0
  • 06/15/15--14:54: opel corsa 1.4 2001
  • hi
    because my Opel Corsa 1.4 engine z14xe gasoline pump always works with ignition on (do not delay)?
    already changed the relay but without effect
    someone has the electric scheme?
    thank y

    0 0
  • 06/15/15--15:00: disables egr and fap
  • can any one help me to disables FAP and EGR from memory 16c xx and 17C xx

    0 0
  • 06/15/15--15:09: electronic circuit diagram
  • hello experts
    is it viable to have the circuit diagram of CAT ECM electronic boards?

    0 0
  • 06/15/15--15:09: Galleto v54 vs Tractor
  • One friend want potency your tractor, is possible use galleto v54 clone with jonh deere? or i will burn it.

    Perhaps by pinout?.

    Regards.

    0 0

    Hi guys, Smile

    I'm a newbie in this area and i want a little help.

    I want to know what i need to have of hardware and software to do clones of ECU and UCH by Renault.

    I ask too, if it's possible change VIN of ECU and UCH "non-virgin"

    Sorry for my bad english and if this topic was discussed early

    Can you help me please???

    Thank's in advance

    0 0
  • 06/15/15--16:03: AVDI and GDS
  • I cannot get my AVDI to connect with GDS. I have driver installed but when connecting I get a message that says that the Dlogger is on and VCI update is required. Try to update VCI through GDS and says it cannot connect to interface. What am I doing wrong?

    0 0
  • 06/15/15--16:14: driver for elm327 Bluetooth
  • hi
    I'm looking driver elm327 Bluetooth for windows 7
    thanksKolo

    0 0
  • 06/15/15--16:23: Steering column lock
  • hello

    I have Virginise a Steering column lock and when I want to program it with the clip it say : condition non satisfaite .
    please someone know what is problem

    0 0
  • 06/15/15--16:37: EGR and DPF question
  • Hi

    Can anyone helpme? I need to delete the EGR and DPF on a cummins ISX engine; I dont mind paying for the information or the calterm delete files.



    ThanksSmile

    0 0

    helo everyone !
    i have an problem with my ECU.
    I reset my ecu with OPcom after i inserted keypass when he ask for.
    after restart i try to start engine but dont work and said :ïmmobilizer failure.
    try starting again!
    please help
    i dont have saab service in my country!

    0 0
  • 06/16/15--12:16: Need code for Becker BE 1100
  • Need code for becker BE1100
    BE1100C4656720

    Best Regards
    Godax

    0 0
  • 06/16/15--12:19: Blaupunkt BNO 881
  • Hi

    Could anybody calculate code from this dump

    Ubit is Skoda Blaupunkt BNO 881

    1U0035191B
    SKZ1Z7G7234954
    7 612 002 030

    8 618 842 980
    2177751

    Eprom 24C32

    BNO881_OK.rar
    File Type: .rar
    Downloaded: 3 times
    Size: 1.37 KB


    0 0

    Hello!

    Can anyone help me at doing a milleage correction at a 2010 bmw 530d?


    I have an digiprog, tachopro, m35080 programmer and a r270

    Can i do this job with this tools?

    And how it works?

    I would pay for the help when the job is done =)


    Sry for my bad english


    Dear regards

    Ossi

    0 0
  • 06/16/15--12:37: POWER
  • I need 228KW and 640 Nm for my Benz.

    S320 CDI with 173KW(W221) Build 2006

    0 0

    Maps Correct for (EGR OFF AUDI A6) is this?

    1C68A6 Map "Bosch 16" (8x1)
    1C690C Map "Bosch 16" (8x1)

    Audi_A6_ori.zip
    File Type: .zip
    Downloaded: 5 times
    Size: 72.28 KB


older | 1 | .... | 581 | 582 | (Page 583) | 584 | 585 | .... | 4905 | newer