Quantcast
Are you the publisher? Claim or contact us about this channel


Embed this content in your HTML

Search

Report adult content:

click to rate:

Account: (login)

More Channels


Showcase


Channel Catalog



Channel Description:

MHH AUTO - https://mhhauto.com

older | 1 | .... | 728 | 729 | (Page 730) | 731 | 732 | .... | 4925 | newer

    0 0
  • 11/28/15--14:19: Detroit 60 series
  • Hello, I've been working on a friends ddec2. He called me and said it quit running and would not start back. Found the hot wire had broken from battery to power junction box. Fixed it and truck started but is now missing and smoking. Checked fuel pressure and was good. Showed injector response times were off. So replaced the injector wiring harness, now have no fault codes. But have the same problem. Replaced both engine timing sensors, and all injectors, tried another ecm as well, truck will not rev much past idle. I am scratching my head on this on. Any help would be greatly appreciated. Thanks to all

    0 0
  • 11/28/15--14:21: odis e
  • hi i'm andy71.I have a problem with flash any ecu.Sameone know step by step to flash ecu with odis e?

    0 0

    Hello, All. I am looking for a wiring diagram for a 97 GMC Yukon for headlight circuits with DRL. we put in new turn signal switch to fix no brake lights on main brake lights and now we have no low beams, put old switch back in and still no low beams. I am looking for a good diagram so we can trace everything out. Thanks in advance if anyone can help

    0 0
  • 11/28/15--14:24: What type off Interface ? :)
  • Hi,
    Really need som help her, it's just to much information on this Site Smile

    What type of cheap interface (below 300usd) will work with
    Nissan consult III Plus ?

    I want to be able to clear / read airbag,abs ecu and tcu codes, reprogram tcu's an maybe Ecu's.

    Car to be used on : Nissan Patrol 98-2010.

    Will any of the following interfaces do the trick ?

    1. newest version of the chines Consult III interface. /the normal one, not the expensive IV)

    2. VAS5054A, if so will it have limitations ?

    3. The Ford Interface.

    4. Renault Clip, if so will it have limitations ?

    Or do i need to downgrade to Consult III (Not plus) and use the chines Consult III interface.

    Cant draw any conclusion my self because of the big amount on info her Big Grin

    Regards
    Spawn

    0 0
  • 11/28/15--14:26: bmw 535i sedan 2010
  • hello mates , since its my first time tis vehicule did any one of you Cas of the above car using the clone m35080 ereaser from ecutool ? what cas inside ?
    i have digiprog 3 , upa , x100 pro , m35080 ereaser all clone

    any of this will help in changing mileage for 2010 bmw 535i sedan ?
    thanks in advance

    0 0
  • 11/28/15--14:32: What type off Interface ? :)
  • Hi,
    Really need som help her, it's just to much information on this Site Smile

    What type of cheap interface (below 300usd) will work with
    Nissan consult III Plus ?

    I want to be able to clear / read airbag,abs ecu and tcu codes, reprogram tcu's an maybe Ecu's.

    Car to be used on : Nissan Patrol 98-2010.

    Will any of the following interfaces do the trick ?

    1. newest version of the chines Consult III interface. /the normal one, not the expensive IV)

    2. VAS5054A, if so will it have limitations ?

    3. The Ford Interface.

    4. Renault Clip, if so will it have limitations ?

    Or do i need to downgrade to Consult III (Not plus) and use the chines Consult III interface.

    Cant draw any conclusion my self because of the big amount on info her Big Grin

    Regards
    Spawn

    0 0

    Hi

    I have a ford f150 newest model year 2015. chip 24c32
    i;ve read bin file but my digiprog cant connect to pc.

    it has 300-400km now, but I need it to 0km.
    could anyone tell me where the mileage is stored in file? then I can FFFFFFFF it..?

    ford.jpg
    File Type: .jpg
    Downloaded: 3 times
    Size: 12.67 KB


    0 0

    Hello, everybody. I was looking for SD Connect 4 to buy and found one for a good price with nice photos of the boards. Before buying i decided to ask seller to confirm if the product exactly the same as on the picture and they replied to me with picture of "new" board they have. I attached picture of it. I would like to ask experienced users if it's a good board because i didn't see it anywhere else (black components). Any comment would be helpful

    SD4c.jpg
    File Type: .jpg
    Downloaded: 4 times
    Size: 413.79 KB


    0 0
  • 11/28/15--15:33: DAS Startup Issue
  • Hello,

    Having a DAS startup issue. XENTRY starts fine, but after selecting vehicle and starting DAS I get the following prompt:

    Star Diagnosis 2014 Registration Dialog

    Name

    Key

    BUTTONS: Try, Register, and Close


    I can't seem to pass this prompt. All keys look OK in Starutils.

    This is with C4 mux and D630 laptop.... seems like software setup issue however.

    Hope we can find a solution for this one. Otherwise the computer is running great.

    0 0

    I am looking for any light that could be shed on this. Any help would be greatly appreciated! I have 2004 Audi A4 USP the stock cluster has a red and black funky pixelated display screen, and I want to replace it with an S4 cluster with the color version of the display screen, then do a milage correction. will everything function as intended?

    Is this possible? I know it has something to do with the immo and SKC code.

    I have Vcds and the Genuine Rosstech cable, other programs not installed on a disk somewhere vag kommander.

    Again any help would greatly appreciated!

    0 0
  • 11/28/15--15:39: introducing my self
  • Hi I'm Fathy from Egypt
    I'm repairing ECU, dashboards and programming keys
    need help with toyota dashboard 2013 south africa odo eeprom 93c86 st
    HeadbangHeadbangHeadbang

    0 0
  • 11/28/15--15:41: Mitsubishi fuso FE145 codes
  • I have a 2007 Fuso with codes P1635 P1630 P0335... It will not let me clear them so Im unsure as to them being active or not. I put a new crank sensor in already. The problem is the truck will run great for a 1/4 mile then under load it will start skipping and has NO power. I think its a fuel related problem but not 100%. The crazy thing it when it is skipping and you pull up to a stop sign it has a skip that doesnt clear up. You can cut the engine off and wait a few minutes and then start it back up and skip is going,. If you pull off and hold it to the floor within a 1/4 mile it will go back to skipping and no power. Anyone with ideas?

    0 0
  • 11/28/15--15:57: DAS license error
  • Hi guys
    does anybody had an error "license key is corrupted"
    when starting DAS (trough Xentry )
    I've changed key several times from different generators, always accepted
    what's going on ?

    error.jpg
    File Type: .jpg
    Downloaded: 9 times
    Size: 130.84 KB


    0 0

    hi, i have a fiat uno novo 1.4 but i cant make a tunning file but i dont understand those maps. i cant find injection maps and i dont understand torque maps. can anyone help me? i need a good tunning file or some help.
    Fiat uno novo 1.4
    HW: IAW7GFHW200
    SW: E205N26
    SW ver.: 7GFE4
    Spare: 51898649

    novo 1.4 ktl173.rar
    File Type: .rar
    Downloaded: 1 times
    Size: 447.91 KB


    0 0
  • 11/29/15--11:19: KESS - PROG
  • Good day
    Who needs to work for with KESS.
    Use THANKS and REPUTATION if my post is helpful...

    kess-prog.txt
    File Type: .txt
    Downloaded: 73 times
    Size: 26 bytes


    0 0
  • 11/29/15--11:27: Cable galetto fg tech
  • Hello,

    iam searching cable for ecu PIN. I want create adapter to read ecu with my own adapter. So i need cable plug from galetto cable to create it fir small pin and big pins from engine ecus to read it with k-line.
    Where can i buy this?


    should looks like this cable plug:
    http://www.xcar360.com/media/0701/fgtech/3.jpg

    Thanks

    0 0
  • 11/29/15--12:08: Opel Vin
  • is it possible found pin from VIN
    Opel Corsa C
    W0L0XCF0814057694

    0 0
  • 11/29/15--12:18: WABCO TEBS-E 4.1
  • WABCO TEBS-E 4.1 for VDI wabco interface
    thanks+rep=pass

    link.rar
    File Type: .rar
    Downloaded: 9 times
    Size: 140 bytes


    0 0

    This is the part nr 4G0035193C
    Thanks

    0 0
  • 11/29/15--12:32: need cat factory password
  • loong for a cat factory password to turn off california emissions. not sure what informations i need to give you


    service tool serial number et061440-6-tf
    esn lee12159-nr
    ecm 05536356qy-vn
    total tattletale 2417
    reason 128
    from 1005
    tp1021

    diagnostic clock4960

older | 1 | .... | 728 | 729 | (Page 730) | 731 | 732 | .... | 4925 | newer