I have a clone reworked ktag. I have a EDC16c3 on the bench & sometimes it will read & write & sometimes it will read but say "reading error". Most times i can't do a backup & is more successfull reading indivudal MPC,Flash,eeprom. Am i doing something wrong or it is a bad ktag?
I have a toyota corolla that has a ecu fail. I was wondering if i replace it with anither used one if im able to program it with immo and with exact software? Or does it work if i program ot with exact software and just turn the immo of?
I've got a 2008 VW Passat - VIN WVWZZZ3CZ9P043783
It's coming up with "Rear side airbag igniter on passenger side - N202-Short circuit to ground"
The workshop has changed the bags from side to side but get the same message every time.
Is there a way to turn in off?
I can get in to the settings with the Maxisys Elite but I need the 5 & 7 digit pin codes to go further.
Jonny Rotten Is proud to introduce to you ECO-DRIVE Performance and repairs,
with Dealers Worldwide,australia, NewZealand, China, Saudi Arabia to mention a few.
We offer Full Tuning,on-road and off-road applications, full remote engine diagnostics, as awell as a dealer network Canada U.S wide for quick and cost effective repairs (dealer list available upon request). We have 6 certified technicians avalable to help with all your diagnostic questions and repairs as well, ecm swaps are available as well as remote tuning avalible, one time use user interfaces are also avail which can be set with any tune you would like.
Full bin file flashing tools available also.
locked or unlocked tuners available for pickup trucks.
All cummins files are available on a insite flashable dongle as well as any bin file of your choice (note dongles are set with a limiter as to what you buy!)
full exhaust kits are available for automotive vehicles as well as industrial, agriculture and trucks, all block off kits are available upon request also.
Also coming soon, tuning for cars, egr dpf, lambda off, as well as dtc, immob and crash data.
Website address will be updated shortly.
Contact Info and pricing Available via pm.
Within the weeks Ahead we will be doing introductory tuning specials... Stay tuned.
Contact myself, Kamiar, or SCANIA730
I have a Seat toledo -99 here that needs immo off, I have searched around and found a possible solution for the immo box itself but several has also reported that solution as non working(00 AA AA)
I have found several threads for 5WP4 immo off but the stock files differs from mine so I don´t think it will work
I have attached both flash/eprom(m27c1001 PLCC32) and eeprom(93c56) files
ANY ONE OUT THERE RUN INTO A 0559 CODE ON A 2250 ISX?
THE CODE ONLY HAPPENS WHEN THE UNIT IS UNDER LOAD, AND IS INTERMITTENT AT BEST.
I HAVE COMPLETED ALL TESTING ON THE LOW PRESSURE SIDE, IT PASSES EVERY TEST, AND THE HIGH PRESSURE SIDE PASSES ALL-EXCEPT THE PERFORMANCE TEST.
FOR THE HIGH PRESSURE FUEL PUMP PERFORMANCE TEST I GOT 120 ML TOTAL AT 150 RPM AND PEAK PRESSURE AT 29000 PSI, BUT AVERAGE PRESSURE, WHILE CRANKING, IS BETWEEN 5000 PSI TO 6000 PSI. (NOTE: THE FUEL APPEARS VERY AERATED WITH VERY SMALL BUBBLES AT THE TOP OF THE DRAIN TUBE.)THE RESULTS CALL TO INSPECT THE PUMP CAMSHAFT AND TAPPET ROLLERS. UPON INSPECTION I FAILED ONE OF THE CHECK VALVES IN THE HEAD. NO CHECK VALVES WERE AVAILABLE SO I REPLACED THE PUMP HEAD. I RETESTED AND GOT THE SAME RESULTS.
I have got a 5054 and online from this web site .. but after a few month the online is not working so I try to contact the support but there is no reply for a month till now ...please share you experience...
I have got problem with Kess v2. When I tried to wirite Renault Laguna II 1.9 130hp Ecu(edc16) by OBD, i noticed error "Change of session not possible". Does anyone know the solution? That's the first car which i am trying to flash. Reading was ok. Software version is v2.06, and firmware is 3.099. I tried to write as "Laguna", and "Megane" as well.
Also I put readed file, so could anyone check, that is it readed ok? https://mega.nz/#!hVtyla6a!NTxmMlRAxfRAS...wvaNG4Im7E
That's photo of Kess PCB: http://imgur.com/SobaYCh
hello everybody ,
I'm thinking of opening a car key copy shop and would like some tips . I wonder if it is possible to copy a key just with the vin code .
Can I use INSTACODE service to get the PINCODE from the VIN ?
Which equipment allows to record the transponder only using the PINCODE ?